#1
| |||
| |||
drdo exam for engineers |
#3
| |||
| |||
Re: drdo exam for engineers
Don’t worry I will provide you Defence Research and Development Organisation, CEPTAM STA Automobile Engineering and Civil Engineering exam paper, for engineers looking to apply in DRDO. Here is the exam paper Civil Engineering 1. The ratio of lateral strain to axial strain of a homogeneous material is known as (a) Yield ratio (b) Hooke’s Law (c) Poisson’s ratio (d) Plastic ratio 2. In the post tensioning system for small, medium and large force, following system is used (a) Freyssinet system (b) PSC monowire system (b) Gifford Udall- CCL system (d) Le-McCall system 3. Principal planes are subject to (a) Normal Stress only (b) Tangential stress only (c) Both normal and tangential stress (d) None of the above 4. The ratio of stress produced by a suddenly applied load and a gradually applied load on a bar is (a) 0.25 (b) 0.50 (c) 1.00 (d) 2.00 5. The point of contraflexure is the point where (a) Bending moment changes sign (b) bending moment is maximum (c) Bending moment is minimum (d) shear force is zero 6. The ratio of maximum shear stress to average shear stress of a circular section is (a) ¾ (b) 4/3 (c) 2/3 (d) 3/2 7. The maximum shear stress due to shear force V on a rectangular section of area A is at the neutral axis and its value is (a) V/A (b) V/2A (c) 3V/2A (d) 2V/3A 8. The ratio of the moment of inertia of a triangular section about its base and an axis parallel to its base through its centre of gravity is (a) 1.0 (b) 1.5 (c) 2.5 (d) 3.0 9. A beam is said to have been subjected to a pure bending when (a) Shear force is constant throughout the span (b) Load is applied as UDL throughout the span (c) Load is applied at the mid span only (d) None of the above 10. A three hinged arch is hinged at supports and (a) At one quarter span (b) at the crown (c) anywhere in arch (d) none of the above Automobile Engineering 1. Which of the following symptom is caused as a result of brake disc run out? (a) Ineffectiveness of the brackes (b) Judder during braking (c) Localized wearing of the brake pads (d) Rapid wearing of the brake pads 2. If the engine coolant leaks into the engine oil, then engine oil (a) Appears milky (b) Becomes foamy (c) Turns black (d) None of these 3. The torque available at the contact between driving wheels and road is known as (a) Brake effort (b) Tractive effort (c) Clutch effort (d) None of these 4. The oil pump is driven by the (a) Camshaft (b) Alternator shaft (c) Crankshaft via drive belt (d) Crankshaft directly 5. The petrol engines are also known as (a) Spark ignition engines (b) Compression ignition engines (c) Steam engines (d) None of these 6. The cetane rating of Diesel fuel is in the order of (a) 90 (b) 45 (c) 70 (d) 25 7. If the air fuel mixture in a spark ignition engine is too rich, then air fuel ratio is about (a) 13:1 (b) 17:1 (c) 15:1 (d) 10:1 8. The natural gas is compressed in a CNG cylinder at a pressure of (a) 300 bar (b) 200 bar (c) 220 bar (d) 250 bar 9. The aluminium alloy is used in cylinder blocks because (a) It is lighter and have good heat dissipation characteristics (b) Material cost is low (c) It does not require any cylinder liners (d) The piston is also made of aluminium alloy 10. What type of bearing is used for main bearings and connecting rod bearings? (a) Ballbearings (b) Plain bearings (c) Needle roller bearing (d) Taper roller bearing Ans- 1 (b) 2 (a) 3 (b) 4 (d) 5(a) 6(b) 7(d) 8 (b) 9(a) 10 (b) |
|